Technique · seat note from Šiauliai
Dampening, mellowing and twisting cattail at the kitchen table
Dry cattail snaps if you try to bend it, and cattail soaked too long turns into wet cardboard in the hand. All of the craft sits between those two states, and a flat with the radiators on full makes the gap between them narrower than any book suggests.
Written 23 March 2025 · checked again 12 October 2025 · 6 minutes at the table
Work tag
- Soak
- A few minutes, cold
- Mellow
- 3 hours to overnight
- Coil
- 2 to 3 leaves
- Joins
- Underneath only
- Squaring
- 4 cm each corner
Round 1
A short soak and a long rest
I prepare only what I will weave in one evening, usually a bundle as thick as my wrist. The leaves go into the bath in cold water for a few minutes, pushed under by hand until the whole length has gone a shade darker, and then they come straight out again. They are rolled up in a wet old sheet, laid on a towel in the bath and left for three or four hours, or overnight if I have planned ahead. Books call this mellowing, which is a good word for it.
The test is simple. A mellowed leaf folds over a finger and back without cracking along the fold, and it feels cool but not wet. If water runs out when I squeeze it, it has had too much and needs an hour on the towel. Leaves that are soaked, dried and soaked again grow weaker each time and start to smell, so anything left at the end of an evening goes back on the airer to dry properly rather than into the sheet.
The heating season changes everything. With the radiators on, the kitchen air is so dry that a coil left on the table for twenty minutes while the kettle boils has stiffened again at the tips. From October to April I keep the working bundle in its sheet on the chair beside me and draw out only two or three leaves at a time, laying a damp cloth over the coil in my lap whenever I stop to measure or to stuff a pocket.
Round 2
Making a coil and twisting it
A coil is two or three leaves worked as one. Cattail leaves are thick at the butt and thin at the tip, so I lay a butt end beside a tip end to keep the coil an even thickness along its length, and draw each leaf through a folded cloth first to squeeze out air and surplus water. For my grandmother's chairs the coil is a little thicker than a pencil. A seat for a heavy stool can take one as thick as a thumb.
The twist only happens where the coil will show on top of the seat. As the coil approaches a rail I twist it, always in the same direction, so that the twist tightens rather than unwinds as I pull it over and round. Underneath, where the strands run back towards the middle, the leaves are left flat and untwisted. That saves material, keeps the underside thin and makes the pockets far easier to stuff later.
Round 3
Joining new leaves underneath
A coil runs short every couple of rounds, and a new leaf has to be joined in. Every join I make is underneath, in the middle of the seat, never on a rail and never where it could show on top. I lay the new leaf alongside the short end, tie the two together with a half knot pulled hard, and let the tails lie flat against the underside, where the next rounds and the stuffing will hold them down.
Joins are also the place to correct thickness. If the last few rounds came out thin, the new leaf goes in butt end first; if they came out fat, I add a tip instead, or drop one of the three leaves altogether for a round or two. I check by running a thumb along the rail where the strands lie side by side, feeling for one that sits proud of the rest. It sounds fussy, and it is the difference between a seat that looks woven and one that looks stuffed.
- Too dry: the leaf cracks white along a fold, or the tips feel papery.
- Right: it folds and springs back, cool to the touch, with no drips.
- Too wet: water runs out when squeezed and the leaf flattens to nothing.
- Gone off: any sour smell or dark spots, and the bundle is dried out again.
Round 4
Squaring the front of a chair
Almost every chair seat is wider at the front than at the back, and the pattern needs a square to work in. Before the first full round I measure the front rail and the back rail between the legs, and the difference is shared between the two front corners. On my grandmother's chairs that comes to about eight centimetres, so four at each corner. A square seat needs none of this, but some old stools are square by accident rather than design, so I measure even the ones that look it.
To fill it, I tack a coil to the inside of the left rail, work only the front left and front right corners, and tack it off on the inside of the right rail. Then I cut, start again on the left and do the same. Each short row fills the front corners a little more, and when the unwoven stretch of the front rail matches the length of the back rail, the full rounds begin. I check that with a tape between the legs rather than trusting my eye, because the eye is always generous.
Round 5
What lives on the table while I work
The kit is small and mostly borrowed from the kitchen. A flat stick of beech, planed smooth, packs the strands against each other. The handle of a wooden spoon opens gaps in the last rounds. A blunt stuffing stick, which began life as a chair spindle, pushes offcuts into the pockets from underneath. There is a tape measure, a bread knife for trimming, a few upholstery tacks and a small hammer, and a spray bottle of water for tips that dry out while I am thinking.
Under all of it goes an old bed sheet, because cattail sheds a fine grey dust as it is worked and a surprising amount of water as it is squeezed. At the end of the evening the sheet is folded inwards and shaken out over the balcony rail, the unused leaves go back onto the airer, and the chair is turned upside down on the table so that the underside can dry overnight before the next round of stuffing.
Written up at the kitchen table in Dainai, Šiauliai, from the notebook kept on the chair beside me. Measurements are from a cloth tape and a caliper; times are evenings, not stopwatches.