Rush Seat WeavingOld chairs and stools re-seated at a kitchen table in Šiauliai

Repair · seat note from Šiauliai

Re-seating my grandmother's kitchen chair, frame first and seat last

I put this chair off for six years, partly for want of skill and partly because it still held a few strands of the seat my grandmother sat on. This winter I finally cut the old seat out, and it turned out to be the easiest part of the whole job.

Written 15 February 2026 · checked again 9 August 2026 · 5 minutes at the table

Work tag

Piece
Kitchen chair
Seat
44 / 36 × 34 cm
Coil
About 7 mm
Glue
Hot hide glue
Evenings
Eleven

Round 1

Reading the old seat before it went

Before anything was cut I photographed the seat from above and from below, counted the rounds on each rail, and measured the old coil with a caliper. It was about seven millimetres thick, twisted to the right on top, and woven from something finer than cattail, probably bulrush. Squaring rows filled the front corners, and a bridge of figure-of-eight passes closed the middle between front and back, which told me the maker had met the same problem I was about to.

Cutting it out took twenty minutes with a craft knife, working from underneath. The pockets were stuffed with dry sedge and, in one corner, a folded page of newspaper printed in 1974, which I have kept in a clear sleeve in the drawer with the tacks. Two small nails still held the first strand to the inside of the left rail. I pulled them with pliers and used the same holes again.

Round 2

Mending the frame

A new seat will not hold a loose chair together. The opposite happens: a chair that racks every time someone sits down will chafe through a new seat in a year. Three of the joints moved, so I knocked them apart with a rubber mallet, gently and a little at a time, scraped the old glue from the tenons and the holes, and reglued them with hot hide glue, which bonds well to traces of old hide glue and can be undone again by whoever mends the chair after me.

The back rail had split along its length where a tack had been driven too close to the end. A neighbour on the ground floor, who turns wood in his garage, turned a new rail from a length of birch, and I rounded over its upper corners with sandpaper so the coil would not cut against them. Clamping was done with a loop of rope twisted tight with a stick, the old way, because I do not own clamps long enough to go round a chair.

  • Photograph and measure the old seat, top and bottom.
  • Cut the seat out from underneath and keep a short sample.
  • Knock apart any joint that moves, then clean and reglue it.
  • Soften every sharp rail corner the coil will pass over.
  • Leave the glue a full day before any weaving starts.

Round 3

Eleven evenings of cattail

The seat is forty-four centimetres across the front, thirty-six across the back and thirty-four from front to back, so it needed four centimetres of squaring at each front corner before the full rounds began. That took the first evening and a half. I kept the coil close to the old one, a little over seven millimetres, which meant three leaves at the butt end of each coil and two at the tip, and a lot of stopping to feel the thickness between finger and thumb.

I stuffed every six or seven rounds with broken leaves and offcuts, pushed in from underneath with a blunt stick, and kept the seams straight by measuring from the legs, as I had learned on the footstool. The work went slowly in January, when the air in the flat was so dry that each evening began with half an hour of damp sheets and ended with my hands smelling of the pond.

Round 4

Stuffing, and the shape of a seat

The old seat had a gentle dome, higher in the middle than at the rails, and a seat without one feels hard and looks thin. The dome comes almost entirely from the stuffing. I pushed offcuts into each of the four pockets every few rounds, packing the middle more firmly than the parts near the rails, and checked the shape by laying a ruler across from side to side and sighting underneath it against the kitchen window.

Too little stuffing, and the strands on top sag into the pockets and wear against the inner corners of the rails. Too much, and the last rounds become so tight that the coil will not pass through the middle. On this chair I got it slightly wrong on the right-hand side, where the triangle sits a few millimetres lower than its partner on the left. Nobody else has noticed, and I have decided to leave it as a note for the next chair rather than unpick a week of work.

Round 5

The bridge, and the waiting

Because the seat, once squared, is a little wider than it is deep, the side rails filled first and left a bare stretch in the middle of the front and back rails. That strip is closed with a bridge: the coil goes over the front rail and up through the middle, across to the back rail, over it and up, then back again, crossing itself in a figure of eight at the centre. It took nine passes and most of the last evening, and the final end was tied underneath to the strand beside it.

Cattail tightens as it dries, so the chair stood in the kitchen for a week before anyone was allowed to sit on it. I gave it no finish at all. My mother came round on a Sunday, sat on it for a while without saying anything, and then said it creaked the way the old ones did. Three chairs are still waiting in the hall, and the page from 1974 is going back into the pockets of the next seat.

Written up at the kitchen table in Dainai, Šiauliai, from the notebook kept on the chair beside me. Measurements are from a cloth tape and a caliper; times are evenings, not stopwatches.

Back to the chair register